Home / Gas Powered Water Pump, 2-inch, 7.5HP 212CC 264GPM, 85.3ft Lift, 26ft Suction, 4-Stroke Portable Water Pump with 24.6ft Hose for Irrigation Pool, EPA Certified

Gas Powered Water Pump, 2-inch, 7.5HP 212CC 264GPM, 85.3ft Lift, 26ft Suction, 4-Stroke Portable Water Pump with 24.6ft Hose for Irrigation Pool, EPA Certified

[Gas Water Pump Parameters] - Water Pump Inlet/Outlet: 2 in; Engine Type: 4-Stroke 212cc; Pump Lift: 85.3ft; Rated Self-suction Height: 24.6ft; Flow: 264GPM; Speed: 3600r/min. The 24.61ft long hose allows for long-distance pumping and large-scale irrigation.
[High Quality Material] - Made of high
Quantity
ADD TO CART
BUY IT NOW
  • Detail

    How to Operate

  • 1. Lay the machine flat and fill it with oil (not included) until just a little oil overflows, as too much or too little oil will affect operation.
  • 2. Add #90 or higher gasoline (not included).
  • 3. Fill the pump head section with water until the water overflows from the outlet.
  • 4. Toggle the red flameout switch to the "ON" position.
  • 5. Adjust the throttle switch and air vent switch to the left and the fuel line switch to the right.
  • 6. Pull a small section of the puller cable out first, and then pull the puller quickly to start the machine.
  • 7. Finally, connect the water inlet and outlet.

    • Specification

  • Material: Cast Iron and Aluminum Alloy
  • Noise: About 66 dB
  • Engine: 4 Stroke, Single Cylinder, Air Cooled
  • Ignition Mode: Non-contact Transistorized Ignition
  • Fuel Tank Running Time: About 5 hours
  • Gasoline Type: 90# and above(Not Included)
  • Emission Control Durability: About 600 Hours
  • Factory Intensive Test Time: About 1000 Hours
  • Working Temperature: -5°-40°C/23°F-104°F
  • Maximum Torque(N.m/r/min): 12/250
  • Fuel Tank Capacity: 3.6L/0.95Gal
  • Oil Tank Capacity: 0.6L/0.16Gal
  • Lift: 26m/85.3ft
  • Suction Distance: 8m/26.25ft
  • Flow Rate: 1000L/264Gal/min
  • Outlet Caliber: 50mm/2"
  • Inlet Caliber: 50mm/2"
  • Hose Length: 7.5m/24.61 ft

    • Notes

  • 1.Please change the oil after the first use of 5-10 hours, otherwise, the impurities in the oil during the break-in period will seize the crankshaft.
  • 2.Please use the correct model, genuine, and clean engine oil. Please add unadulterated 90# gasoline or above to the fuel tank of the machine, add oil to the tank, and check the oil level before each use. We recommend that you use unleaded gasoline for the optimal performance of your product.
  • 3.When the gasoline engine is working continuously, the crankcase temperature should not exceed 90°C. When heating, it should be shut down for 15-20 minutes before continuing to work, and when adding gasoline, it must be cooled down before proceeding.
  • 4.It is prohibited in high-speed shutdown. Please stop the machine when the throttle is at its lowest point!
  • 5.If the machine is not going to be used for a long time, please do not turn off the gasoline engine switch directly, but close the throttle door switch to consume the gasoline in the carburetor; otherwise, it will lead to oxidation of the carburetor.
  • 6.The carburetor plug generally does not need to be replaced, carbon deposits can be removed and scraped down with a razor blade(not included).
  • 7.Please use it outside, but do not operate it in the garage, in rain, water, or after watering, and do not open nearby doors or windows when operating it, and watch out for the high temperature.
  • Customer Reviews
    No comments
    • BACK